RCModelScout.

Flying-Hobby

600DFC MAIN SHAFT(ESP)

Instruction:, ●This main shaft is only for T-REX 600ESP model to fit with 600DFC head. Please do not use it on other models and purposes., Specification:, ●600DFC Main shaft(ESP) x 2(172.7mm),

Flying-Hobby

SCORPION COMMANDER V 50V 130A ESC (SBEC)

BRK= BRAKE SETTING: 1: NO BRAKE, * 2: VERY SOFT BRAKE, 3: SOFT BRAKE, 4: HARD BRAKE, 5: VERY HARD BRAKE, PCT= PROGRAM CUT TYPE (LVC TYPE): 1: CUT 50%*, 2: NO CUT JUST LED WARNING, 3: PULSE WARNING, MAT= MOTOR ACCELERATION TIME DELAY: 1: 0.15 Seconds* (recommend for AIR 2), 2: 0.3 Seconds, 3: 0.45 Seconds, 4: 0.7 Seconds, 5: 1.3 Seconds, COP= CURRENT OVERLOAD PROTECTION: 1: PROTECTION ON*, 2: PROTECTION OFF (CHOOSING OPTION 2 WILL VOID WARRANTY), FREQ= DRIVE FREQUENCY: 1: 8 kHz *, TIM= MOTOR TIMING: 1: AUTO TIMING*, 2: 5 Degrees (Recommend for GOV 1), 3: 15 Degrees, 4: 20 Degrees, 5: 25 Degrees, 6: 30 Degrees,

Flying-Hobby

CARBON CANOPY MOUNT SET (FOR MH-MCPX005/B)

Flying-Hobby

KDE DIRECT ALIGN TREX 500 SERIES PERRFORMANCE TAIL UPGRADE V2

Note: the Performance Tail Upgrade V2 provides superior tail control for sport and hard 3D flying styles.  With dual flanged, radial ball bearing supported tail grips and precise machining tolerances for the brass bushing sleeve, the new design provides a truly slop-free, high-performance tail that is rock-solid for all maneuvers.  The design is a simple retrofit for the common parts on the helicopter (replaces the stock plastic tail control links), with the ability to be used on all TREX 500 helicopters on the market and installed in a matter of minutes., Includes:, - Two (2) TREX 500 Aluminum Tail Control Link V2 Upgrades, Finish:, Clear anodize, brushed CNC matte,

Flying-Hobby

BEARING(685ZZ)

Instruction:, Use for 600 brushless motor, Specification:, Bearing 685ZZ x 2(Φ5xΦ11x5mm),

Flying-Hobby

BL 700H HIGH VOLTAGE BRUSHLESS SERVO

Instruction:, ●Utilizes brushless motor design for fast speed, high efficiency. And with the absence of brush wear, the longevity of servo is greatly increased., ●Designed specifically for helicopters, with highest specifications on the market: 0.065sec/60°ultra fast speed and 20kg-cm monstrous torque, allowing helicopter to perform with faster and higher precision., Specification:, Accessories:, ●Servo rudder piece x 4,

Flying-Hobby

RJX FS-0521 HV STANDARD DS SERVO

Technical Data:,

Flying-Hobby

RJX FS0391 MINI CYCLIC SERVO X3 (COMBO)

Combo Included :, 1. RJX-FS0391  Servo x 3 pcs, Specification:, , Torque:, 8.4kg/cm(116.7oz/in)@6V, :0.035(sec/60°)@6V,

Flying-Hobby

RJX FS-0521T HV STANDARD DS TAIL SERVO

Spec:, Digital HV Standard Tail Servo, :0.035(sec/60°)@6V,

Flying-Hobby

LENSMAN-18 LANDING GEAR CONNECTING FRAME

Feature:, -Used for Lensman-18 Camera 3-Axis Gimbal, Item Included:, 2x Lensman-18 Landing Gear Connecting Frame,

Flying-Hobby

FUTABA DIGITAL SERVO S3153

Flying-Hobby

MPA - MULTI-PORT SAFE PARALLEL ADAPTER FOR XH COMPATIBLE BATTERY PACKS

for full details on this amazing new adapter, only from Revolectrix. Unit includes: support for safe parallel charging of up to 6 same-cell-count packs at one time (2s-8s); supports 40A max charge/discharge rate; every port reverse polarity fuse protection of main battery wires; every cell/balance wire protected by self-resetting polyfuses with temperature warning indicators; supports non-balanced charge of up to two 1s LiPos used with "indoor models"; supports 1 RX and 1 TX NiCd/NiMH battery pack. Works with any Cellpro charger or battery workstation equipped with "XH MODE WIRING" option. Interconnect cables available separately to support Cellpro PowerLab 6/PowerLab 8, Cellpro 10XP, as well as other brand chargers which are compatible with XH balance plugs and wiring. Be sure to purchase the proper cable to plug the MPA into your Charger or Battery Workstation.,

Flying-Hobby

ADJUSTABLE THRIPLE-BEARING ALUMINUM ENGINE BEARING BLOCK

Description:, -The new precision ADJUSTABLE thriple-bearing aluminum engine block is designed to replace stock plastic engine block for T-REX 700 Nitro helicopters. This new version adds ability to adjust the gear mesh between the pinion and the main gear.  Therefore the main gear is less stripped due to inappropriate alignment. The new aluminum engine block is designed with rigid one-piece aluminum block to avoid wear-out problem that leads to unalignment of the pinion to the main gear, thus causing the gear strip problem.  The bearing block is very well designed to have both rigidity, precision and very light weight. To further strengthen the engine clutch, this new design incorporates an additional third bearing into the engine block.  This additional bearing provides great support for the motor pinion shaft to keep the pinion always aligns with the main gear.  This engine block is the ticket to solve main gear strip problem on the T-REX 700 helicopters., Includes:, -One aluminum engine block, Features:*,

Flying-Hobby

APC PROPELLER 14X4.7SFP (CW)

Introduction:, This is the Genuine APC Composite 14x4.7 Propellers. APC Propellers are the most carefully and accurately molded in the USA. The blade shapes are rated as the most efficient and silent manufactured in the aircraft models., Specification:, Items Included:, 1x APC Propeller 14x4.7SFP (CW),

Flying-Hobby

APC PROPELLER 14X4.7SF (CCW)

Introduction:, This is the Genuine APC Composite 14x4.7 Propellers. APC Propellers are the most carefully and accurately molded in the USA. The blade shapes are rated as the most efficient and silent manufactured in the aircraft models., Specification:, Items Included:, 1x APC Propeller 14x4.7SF (CCW),